ADHERIT 1K-phosphate primer is a versatile corrosion protection and adhesion primer. Can be used in many cases even under 2-component top coats. ADHERIT is characterized by fast drying, excellent adhesion to ferrous and non-ferrous metals and good corrosion protection. The dry film quality can be compared with that of stoving primers.

FERROTOL is an air- and oven-drying, thick-layer applicable one-coat paint for interior use. Adheres directly to iron, cast iron and zinc. Coating thicknesses of up to 150 µm are achieved in a single operation. Due to its excellent adhesion to various metals, FERROTOL can also be used as an adhesion primer. The most important properties of FERROTOL are its extremely fast drying and excellent corrosion protection. FERROTOL can also be used as a shop primer. If necessary, it can be painted over with suitable top coats after only 30 minutes.

INDUPLAST ACR 1K-primer is a versatile, fast drying rust protection and adhesion primer. This thick-film product is suitable for use in steel constructions. Furthermore as intermediate coat on 1-component zinc dust paints, hot-dip galvanizing, spray galvanizing, if an alkyd resin paint is subsequently used as top coat.

ECLON PUR C3 is an extremely extensive, thick layer 2-component PUR coating with good resistance properties. Excellent adhesion to various substrates. The essential advantages at a glance: – Economically extremely interesting thanks to high solid matter (less VOC steering charge, environmentally friendly) – Rational processing: rapid drying even at low temperatures – Excellent durability, no run-off, even with thick layers. – Good UV resistance – Resistant to water, acids, alkalis, washing lye, etc.

ACQUA-ETUVA 1K-phosphate primer is a water-dilutable corrosion protection primer. The solvent content is almost 5 %, which meets today's requirements for environmental protection. ACQUA-ETUVA 1K-phosphate primer offers very good corrosion protection, good condensation water resistance and excellent adhesion to iron, cast iron, aluminium and galvanized substrates. The primer can therefore also be used as an adhesive primer. ACQUA-ETUVA can also be easily overpainted with conventional (solvent-based) topcoats. Resistant to aqueous solutions of salts, drilling and cutting oils and to diluted acids and alkalis. The resistance to solvents is limited.

ACQUAFERROTOL 1K-micaceous silk matt is a water-dilutable, air- and oven-drying, thick-layer applicable material with best direct adhesion on iron and cast iron surfaces. ACQUAFERROTOL used both as a one-coat paint and as a primer with excellent corrosion protection under various top coats (including solvent-based). Coating thicknesses of up to 100 µm are achieved in a single operation. ACQUAFERROTOL also stands out for its rapid drying and good resistance to condensation water. ACQUAFERROTOL can also be used as an adhesion primer on existing coatings. Resistant to aqueous solutions of salts, drilling and cutting oils and to diluted acids and alkalis. The resistance to solvents is limited.

COPRASOL is a moisture-curing 1-component adhesion promoter based on polyurethane resin. COPRASOL 1K-FH deep ground is used as an adhesive primer for mineral substrates such as concrete, plaster, eternit, etc. It acts simultaneously as a deep penetrating primer and as such solidifies the mineral subsoil.

COROPUR 1K-FH intermediate micaceous iron coating is primarily used, in combination with moisture-curing systems, as an intermediate coating in corrosion protection systems from corrosivity category C3. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR 89 1K-FH intermediate micaceous iron coating is primarily used, in combination with moisture-curing systems, as an intermediate or top coat in interior areas. Corresponds to the specifications according to TL/TP-KOR – Steel structures; Annex E; Sheet 89. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR 89 can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

FERROTOL is an air- and oven-drying, thick-layer applicable one-coat paint for interior use. Adheres directly to iron, cast iron and zinc. Coating thicknesses of up to 150 µm are achieved in a single operation. Due to its excellent adhesion to various metals, FERROTOL can also be used as an adhesion primer. The most important properties of FERROTOL are its extremely fast drying and excellent corrosion protection. FERROTOL can also be used as a shop primer. If necessary, it can be painted over with suitable top coats after only 30 minutes.

INDUPLAST ACR 1K-patina effect lacquer is a fast drying 1-component duplex system. It is particularly suitable as a top coat for hot-dip galvanizing and zinc dust primers. As an effect varnish it shows a uniform and decorative structure, which is supposed to simulate patination. A very good gloss and chalking resistance is given.

INDUPLAST ACR are broadly applicable, fast drying, light and weather resistant coatings. Particularly suitable for the protection of fresh and weathered hot-dip galvanized coatings (DUPLEX system). In combination with suitable primers, can also be used as a corrosion protection top coat for iron and steel structures in exterior and interior areas. INDUPLAST ACR is resistant to various weak acids and alkalis, but not to organic solvents.

INDUPLAST ACR are broadly applicable, fast drying, light and weather resistant coatings. Particularly suitable for the protection of fresh and weathered hot-dip galvanized coatings (DUPLEX system). In combination with suitable primers, can also be used as a corrosion protection top coat for iron and steel structures in exterior and interior areas. INDUPLAST ACR is resistant to various weak acids and alkalis, but not to organic solvents.

INDUPLAST ACR are broadly applicable, fast drying, light and weather resistant coatings. Particularly suitable for the protection of fresh and weathered hot-dip galvanized coatings (DUPLEX system). The coating can be used for exterior and interior applications as a one-coat paint. The coating is equipped with conductive pigments. A contact resistance of < 10⁹ Ω is achieved. This makes the coating dissipative. INDUPLAST ACR is resistant to various weak acids and alkalis, but not to organic solvents.

ACQUAFERROTOL 1K-micaceous silk matt is a water-dilutable, air- and oven-drying, thick-layer applicable material with best direct adhesion on iron and cast iron surfaces. ACQUAFERROTOL used both as a one-coat paint and as a primer with excellent corrosion protection under various top coats (including solvent-based). Coating thicknesses of up to 100 µm are achieved in a single operation. ACQUAFERROTOL also stands out for its rapid drying and good resistance to condensation water. ACQUAFERROTOL can also be used as an adhesion primer on existing coatings. Resistant to aqueous solutions of salts, drilling and cutting oils and to diluted acids and alkalis. The resistance to solvents is limited.

ACQUATOL is a water-dilutable, quick-drying spray paint for weather-resistant and chalking-resistant coatings.

ACQUATOL is a water-dilutable, quick-drying spray paint for weather-resistant and chalking-resistant coatings.

ACQUATOL is a water-dilutable, quick-drying spray paint for weather-resistant and chalking-resistant coatings.

ACQUATAL is a water-thinnable one-coat stoving enamel for th varnishing of iron and aluminium.

Primer and paint coating in one. The moisture-curing PU coating contains active corrosion protection pigments and thus combines the high mechanical properties of polyurethane with the corrosion protection properties of comparable cross-linked systems. It is also characterized by very fast drying, which results in shorter service lives. The dry layer can be cleaned with solvent (grease, etc.) after assembly. Easy repair even under bad conditions.

COROPUR 1K-FH intermediate micaceous iron coating is primarily used, in combination with moisture-curing systems, as an intermediate coating in corrosion protection systems from corrosivity category C3. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR LS 1K-FH finishing micaceous iron coating serves primarily, in combination with moisture-curing systems, as a high-quality top coat. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR LS can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR 89 LS 1K-FH finishing micaceous iron coating serves primarily, in combination with moisture-curing systems, as a high-quality top coat. Corresponds to the specifications according to TL/TP-KOR – Steel structures; Annex E; Sheet 89. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR 89 LS can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR is a moisture-curing, light, weather and chemical resistant top coat based on polyurethane resin. COROPUR can be applied at low temperatures and high humidity without any problems. The rapid drying and hardening of the coating film allows the coated objects to be manipulated quickly, thus reducing downtimes.

COROPUR is a moisture-curing, light, weather and chemical resistant top coat based on polyurethane resin. COROPUR can be applied at low temperatures and high humidity without any problems. The rapid drying and hardening of the coating film allows the coated objects to be manipulated quickly, thus reducing downtimes.

COROPUR 89 is a moisture-curing, light, weather and chemical resistant top coat based on polyurethane resin. COROPUR 89 can be applied at low temperatures and high humidity without any problems. The rapid drying and hardening of the coating film allows the coated objects to be manipulated quickly, thus reducing downtimes. Corresponds to the specifications according to TL/TP-KOR – Steel structures; Annex E; Sheet 89.

ACQUAPOX EP 2K-phosphate primer is a water-dilutable adhesion and corrosion protection primer based on epoxy resins. Fulfils the requirements of Armasuisse painting instructions M 040 216 and M 040 217 and serves as an anti-corrosion primer or intermediate primer with excellent adhesion and mechanical resistance for almost all scaffolding materials according to Armasuisse painting instructions M 040 106-04.

ECLAPOX EP 2K-phosphate primer and the ECLAPOX EP Quick variant, which is created by using the appropriate hardener, offer protection and adhesion in one. Both are particularly characterized by fast drying, high mechanical strength, chemical resistance and very good adhesion and corrosion protection. ECLAPOX EP can also be processed at temperatures down to 0 °C.

ECLAPOX HS 2K-phosphate primer offers protection and adhesion in one. Particularly characterized by fast drying, high mechanical strength, chemical resistance and very good adhesion and corrosion protection.
According to Armasuisse paint regulation M 040 230

ECLON EP 2K-phosphate primer and the ECLON EP Quick variant, which is created by using the appropriate hardener, offer protection and adhesion in one. Both are particularly characterized by fast drying, high mechanical strength, chemical resistance and very good adhesion and corrosion protection. ECLON EP can also be processed at temperatures down to 0 °C.
As such, fulfils the conditions of BN 108 / BN 109.

ECLON EP 87 2K-zinc dust primer is a 2-component epoxy resin corrosion protection primer with excellent adhesion on blasted substrates. Characterized by highest durability and can be overpainted with any saponification-resistant 1- and 2-component system. Approved and monitored according to sheet 87 and 94 TL/TP – KOR, steel structures.

ECLON EP 87 2K-phosphate primer offers protection and adhesion in one. It is particularly characterized by high mechanical strength, chemical resistance and very good adhesion and corrosion protection. Fulfils the requirements of sheet 87 of TL/TP – KOR, steel structures.

ECLON EP 2K-Washprimer provides excellent adhesion of air- and oven-drying top coats on various substrates. Due to its phosphating and passivating properties it also provides minimal corrosion protection.

ECLON PUR 2K-phosphate primer is a corrosion protection primer with excellent adhesion and mechanical resistance for the entire steel and metal construction sector. Thanks to «wet-on-wet» application in combination with PUR topcoats, the drying time for the entire system is significantly reduced.

ECLON PUR is a high solids, solvent and weather resistant multi-purpose filler based on 2-component polyurethane and acrylic resin. It is characterised by its good drying and can be sanded after only about 3 hours drying at 20 °C. If sanding is not required (e.g. in mechanical engineering), the dried layer can be sprayed over after 60 minutes of drying at 20 °C. ECLON PUR 2K-primer and spray filler contains active corrosion protection pigments and can also be used as a highly filling primer for exterior use.

ECLON EP 2K-micaceous iron is a high-quality scale armour coating with high mechanical and chemical resistance. Dry film thicknesses of up to 150 µm can be achieved in a single pass. The pigmentation with micaceous iron ore creates a rough surface in addition to the barrier effect desired in corrosion protection. The best prerequisite for a perfectly adhering PU-based top coat.

ECLON EP 87 2K-micaceous iron is a high-quality scale armour coating with high mechanical and chemical resistance. Dry film thicknesses of up to 150 µm can be achieved in a single pass. The pigmentation with micaceous iron ore creates a rough surface in addition to the barrier effect desired in corrosion protection. The best prerequisite for a perfectly adhering PU-based top coat.

ECLON EP 2K-adhesive compound is a solvent-free adhesive coating based on polyurethane epoxy resin. In combination with ECLON EP 87 2K-micaceous iron as a primer, the ECLON EP 2K-adhesive compoundProvides the necessary bond between the protective layer and the orthotropic steel roadway slab. It firmly binds the chippings and shows no change in properties after application of mastic asphalt.

ECLON EP stands out as an intermediate or top coat on corresponding primers (e.g. ECLON EP 87 2K-zinc dust primer or ECLON EP 2K-phosphate primer ) due to its excellent chemical and solvent resistance. Used as a one-coat paint, it produces silky gloss and very well adhering coatings on steel and galvanized substrates.

ECLON PUR is a high solids, solvent and weather resistant multi-purpose filler based on 2-component polyurethane and acrylic resin. It is characterised by its good drying and can be sanded after only about 3 hours drying at 20 °C. If sanding is not required (e.g. in mechanical engineering), the dried layer can be sprayed over after 60 minutes of drying at 20 °C. ECLON PUR 2K-primer and spray filler contains active corrosion protection pigments and can also be used as a highly filling primer for exterior use.

ECLON PUR DA 2K mica is a thick-film topcoat for best weather and chemical resistance. ECLON PUR DA 2K mica is suitable both as a one-coat paint and as a top coat for paint structures and for coating hot-dip galvanizing (duplex systems). The adhesion to iron, aluminium and zinc is excellent. The essential advantages at a glance: – Rapid drying – Excellent weather resistance – Resistant to water, acids, alkalis, washing lye, etc. – Good adhesion to aluminium and the various galvanized surfaces.

ECLON PUR DA 2K-micaceous iron is a thick-film topcoat for best weather and chemical resistance. ECLON PUR DA 2K-micaceous iron is suitable both as a one-coat paint and as a top coat for paint structures and for coating hot-dip galvanizing (duplex systems). The adhesion to iron, aluminium and zinc is excellent. The essential advantages at a glance: – Rapid drying – Excellent weather resistance – Resistant to water, acids, alkalis, washing lye, etc. – Good adhesion to aluminium and the various galvanized surfaces.

ECLON PUR C3 is an extremely extensive, thick layer 2-component PUR coating with good resistance properties. Excellent adhesion to various substrates. The essential advantages at a glance: – Economically extremely interesting thanks to high solid matter (less VOC steering charge, environmentally friendly) – Rational processing: rapid drying even at low temperatures – Excellent durability, no run-off, even with thick layers. – Good UV resistance – Resistant to water, acids, alkalis, washing lye, etc.

ECLON PUR DS is an extremely versatile, highly weather-resistant 2-component topcoat for exterior and interior use. Produces thick-film surfaces, both smooth and structured. Depending on the degree of dilution, spray pressure and nozzle size, different structural effects can be achieved. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. This often eliminates time-consuming sanding and filling work. Simple processing without runner formation, even with complicated geometry. Excellent direct adhesion to a wide variety of substrates. Very good colour and gloss resistance to weathering and very good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLON PUR DS is an extremely versatile, highly weather-resistant 2-component topcoat for exterior and interior use. Produces thick-film surfaces, both smooth and structured. Depending on the degree of dilution, spray pressure and nozzle size, different structural effects can be achieved. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. This often eliminates time-consuming sanding and filling work. Simple processing without runner formation, even with complicated geometry. Excellent direct adhesion to a wide variety of substrates. Highly elastic (Buchholz hardness ~ 30–50) and abrasion resistant (Taber abrader approx. 12 mg / 1'000 U at 1 kg load). Very good colour and gloss resistance to weathering and very good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECOLON PUR DS 2K-soft enamel silk gloss is a 2-component paint with a high solid content and is particularly characterised by its high resistance to moisture, salt, industrial dirt, solvents and chemicals. ECOLON PUR DS has excellent weather and chemical resistance, good filling power, does not wrinkle or yellow.

ECLON PUR is a highly weather-resistant, fast drying 2-component coating based on polyurethane resin for exterior and interior use. Simple processing without runner formation, even with complicated geometry. Produces, depending on the colour shade, silk matt to silk gloss, smooth surfaces, which should simulate a patina (métallisé effect). Excellent direct adhesion to a wide variety of substrates. Very good surface hardness and scratch resistance as well as resistance to diluted chemicals, hand perspiration, coolant and cleaning agents.

ECLON PUR ACR 2K-enamel matt is a two-component paint based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity. Approval Type «W» (chemical industry approval) according to BN 108/109 in the systems «WBZ» and «WBR».

ECLON PUR ACR 2K-enamel satin matt is a two-component paint based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity. Approval Type «W» (chemical industry approval) according to BN 108/109 in the systems «WBZ» and «WBR».

ECLON PUR ACR 2K-enamel silk gloss is a two-component paint based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity. Approval Type «W» (chemical industry approval) according to BN 108/109 in the systems «WBZ» and «WBR».

ECLON PUR ACR 2K-enamel gloss is a two-component paint based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity. Approval Type «W» (chemical industry approval) according to BN 108/109 in the systems «WBZ» and «WBR».

ECLON PUR ACR 2K-enamel pearl effect is a two-component paint based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity. Approval Type «W» (chemical industry approval) according to BN 108/109 in the systems «WBZ» and «WBR».

ECLON PUR ACR is a colorless, highly weather-resistant two-component protective coating based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: – No yellowing – No bubble formation, even with thicker layers

ECLON PUR ACR is a colorless, highly weather-resistant two-component protective coating based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: – No yellowing – No bubble formation, even with thicker layers

ECLON PUR ACR is a colorless, highly weather-resistant two-component protective coating based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: – No yellowing – No bubble formation, even with thicker layers

ECLON PUR ACR is a colorless, highly weather-resistant two-component protective coating based on polyurethane resin. ECLON PUR ACR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR ACR has the following properties: – No yellowing – No bubble formation, even with thicker layers

ECLON PUR HS is a top coat based on polyurethane resin for exterior and interior use. Conforms to Armasuisse regulations M 040 231. Excellent colour and weather resistance as well as very good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLON PUR ACR is a top coat based on polyurethane resin for exterior and interior use. Conforms to Armasuisse regulations M 040 218-05. Excellent colour and weather resistance as well as very good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLON PUR LM is a polyurethane-based paint for interior use. Produces solvent-resistant, silky gloss and thick-film smooth or structured surfaces. Depending on the degree of dilution, spray pressure and nozzle size, different structural effects can be achieved. Excellent direct adhesion to a wide variety of substrates. Simple processing without runner formation, even with complicated geometry. Very good surface hardness and scratch resistance as well as resistance to diluted chemicals, hand perspiration, coolant and cleaning agents.

ECLON PUR ACR 2K-micaceous iron is a high solids, highly weather-resistant corrosion protection coating based on polyurethane and acrylic resin. The dry film is highly resistant to moisture, salt, industrial fumes, solvents and many chemicals. Other notable properties of ECLON PUR ACR 2K-micaceous iron are: – Good filling power – No wrinkling – Resistant to water, acids, alkalis, washing lye, etc. – No bubble formation, even with thicker layers – Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

ECLON PUR 87 is an extremely versatile, highly weather-resistant 2-component topcoat for exterior and interior use. Produces thick-film surfaces, both smooth and structured. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. This often eliminates time-consuming sanding and filling work. Simple processing without runner formation, even with complicated geometry. Excellent direct adhesion to a wide variety of substrates. Very good colour and gloss resistance to weathering and very good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLON PUR ACR 87 2K-micaceous iron is a high solids, highly weather-resistant corrosion protection coating based on polyurethane and acrylic resin. The dry film is highly resistant to moisture, salt, industrial fumes, solvents and many chemicals. Other notable properties of ECLON PUR ACR 87 2K-micaceous iron are: – Good filling power – Resistant to water, acids, alkalis, washing lye, etc. – No bubble formation, even with thicker layers – Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

ECLADUR 2K-PUR vehicle paint matt is a two-component paint based on polyurethane resin. ECLADUR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLADUR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

ECLADUR 2K-PUR vehicle paint silk matt is a two-component paint based on polyurethane resin. ECLADUR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLADUR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

ECLADUR 2K-PUR vehicle paint silky gloss is a two-component paint based on polyurethane resin. ECLADUR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLADUR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

ECLADUR 2K-PUR vehicle paint gloss is a two-component paint based on polyurethane resin. ECLADUR is especially characterized by high resistance to moisture, salt, industrial dirt, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLADUR has the following properties: Good filling power / No wrinkling / No yellowing / No bubble formation, even with thicker layers / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

ECLAPUR 609 is an extremely versatile, highly weather-resistant 2-component topcoat for exterior and interior use. Produces silky, thick-layered, structured surfaces and slight unevenness of the substrate can be levelled. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. This often eliminates time-consuming sanding and filling work. Simple processing without runner formation, even with complicated geometry. Excellent direct adhesion to a wide variety of substrates. Very good colour and gloss resistance to weathering and very good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLAPUR 143 2K-PUR textured paint satin matt is a ready-to-spray 2-component textured topcoat specially designed for forced drying. Uniform, textured spray pattern with a silk matt appearance ‒ depending on the applied texture pattern. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. Simple processing without runner formation, even with complicated geometry.
Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLAPUR 143 2K-PUR textured paint matt is a ready-to-spray 2-component textured topcoat specially designed for forced drying. Uniform, textured spray pattern with a matt appearance ‒ depending on the applied texture pattern. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. Simple processing without runner formation, even with complicated geometry.
Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc.

ECLAPUR 144 2K-PUR textured paint fine satin matt is a ready-to-spray 2-component textured topcoat specially designed for forced drying. Uniform, textured spray pattern with a silk matt appearance ‒ depending on the applied texture pattern. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. Simple processing without runner formation, even with complicated geometry.
Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. Also available as THIX version.

ECLON DS is an extremely versatile, highly weather-resistant 2-component topcoat for exterior and interior use. Produces silky, thick-layered, structured surfaces and slight unevenness of the substrate can be levelled. The structural effect covers scratches, grinding marks, casting roughness and other irregularities on material surfaces. This often eliminates time-consuming sanding and filling work. Simple processing without runner formation, even with complicated geometry. Excellent direct adhesion to a wide variety of substrates. Very good colour and gloss resistance and good surface hardness and scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant, cleaning agents, hydraulic oils, etc.

ECLON PUR AS 2K-enamel silky gloss is a real innovation in the field of 2-component polyurethane coatings. ECLON PUR AS is characterized by a particularly high solid content (around 90 % in the ready-to-spray state) and rapid drying behavior compared to conventional materials. ECLON PUR AS can be applied at low temperatures and high humidity without any problems. The dry film is highly resistant to moisture, salt, industrial fumes, solvents and many chemicals. In addition to its excellent weather and chemical resistance, ECLON PUR AS has the following properties: High solid state / Good filling power / No wrinkling / No yellowing / No bubble formation even in thick layers and applied in high and low viscosity, even with accelerated drying. / Efficient working thanks to fast drying even at low temperatures (5 °C), thus fast masking and higher productivity.

COPRASOL is a self-levelling 2-component coating compound based on polyurethane. Is used for jointless floor coverings on all common substrates. COPRASOL 2K-PUR floor paint produces tough elastic coatings with good thermal insulation and high impact and abrasion resistance. COPRASOL is dirt-repellent and easy to clean.

ECLON EP stands out as an intermediate or top coat on corresponding primers (e.g. ECLON EP 87 2K-zinc dust primer or ECLON EP 2K-phosphate primer ) due to its excellent chemical and solvent resistance. Used as a one-coat paint, it produces silky gloss and very well adhering coatings on steel and galvanized substrates.

ECLON EP 2K-silicone textured coating silk gloss produces uniformly structured, very well adhering, mechanically highly resistant (abrasion resistant) coatings on steel and galvanized substrates as well as on various suitable primers.

ECLON EP is a good chemical and solvent resistant 2-component epoxy topcoat. As such, fulfils the conditions of BN 108 / BN 109.

COROPUR NonAbrasive 2K-FH finishing coating RHK 11 is a moisture-curing 1-component polyurethane resin coating with an anti-slip surface structure. The system is equipped with fillers, which give the surface an appropriate roughness, which leads to the anti-slip properties.
The coating achieves a coefficient of friction µ > 0.45 according to DIN 51151. This results in the rating GS3 in the footwear area and GB2 in the barefoot area. According to the «Assessment of slip hazards under operating conditions» published by the German Social Accident Insurance, the coating achieves the highest rating of «safe, falls unlikely». The resulting anti-slip properties depend on the nature of the substrate and the application quantity.
COROPUR NonAbrasive 2K-FH finishing coating RHK 11 is particularly characterized by high abrasion resistance and chemical resistance. The light and weather resistance is good even in high sunlight.

COROPUR NonAbrasive 2K-FH finishing coating RHK 12/13 is a moisture-curing 1-component polyurethane resin coating with an anti-slip surface structure. The system is equipped with fillers, which give the surface an appropriate roughness, which leads to the anti-slip properties.
The coating achieves a coefficient of friction µ > 0.60 according to DIN 51151. This results in the rating GS4 in the footwear area and GB3 in the barefoot area. According to the «Assessment of slip hazards under operating conditions» published by the German Social Accident Insurance, the coating achieves the highest rating of «safe, falls unlikely». The resulting anti-slip properties depend on the nature of the substrate and the application quantity.
COROPUR NonAbrasive 2K-FH finishing coating RHK 12/13 is particularly characterized by high abrasion resistance and chemical resistance. The light and weather resistance is good even in high sunlight.

ACQUAPUR 2K-camouflage paint Armasuisse is a water-dilutable top coat based on polyurethane resin for exterior and interior use. Conforms to Armasuisse regulations M 040 218-06. ACQUAPUR stands out in particular Very high surface hardness and very good scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. A very good colour and gloss retention.

ACQUAPUR DS 2K-textured paint silk gloss is a water-dilutable top coat based on polyurethane resin for exterior and interior use. Produces silky, thick-layered, structured surfaces and slight unevenness of the substrate can be levelled. ACQUAPUR DS stands out in particular Very high surface hardness and very good scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. A very good colour and gloss retention.

ACQUAPUR DS 2K-finishing enamel silky gloss is a water-dilutable top coat based on polyurethane resin for exterior and interior use. Produces thick-film surfaces, both smooth and structured. ACQUAPUR DS stands out in particular Very high surface hardness and very good scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. A very good colour and gloss retention.

ACQUAPUR DS 2K-finishing enamel satin matt is a water-dilutable top coat based on polyurethane resin for exterior and interior use. Produces thick-film surfaces, both smooth and structured. ACQUAPUR DS stands out in particular Very high surface hardness and very good scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. A very good colour stability.

ACQUAPUR DS 2K-finishing enamel matt is a water-dilutable top coat based on polyurethane resin for exterior and interior use. Produces thick-film surfaces, both smooth and structured. ACQUAPUR DS stands out in particular Very high surface hardness and very good scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. A very good colour stability.

ACQUAPUR ACR 2K-finishing enamel gloss is a water-dilutable top coat based on polyurethane resin for exterior and interior use. ACQUAPUR ACR stands out in particular Very high surface hardness and very good scratch resistance. Good resistance to diluted chemicals, hand perspiration, coolant up to 50 °C, cleaning agents, hydraulic oils, etc. A very good colour and gloss retention.