COROZINC M is a primer specially designed for use with permanent water exposure (steel hydraulic engineering). Contains 92 % metallic zinc. Moisture-curing zinc dust primers PU are significantly more elastic than conventional 1- and 2-component zinc dust primers. This means, especially with higher coating thicknesses, much higher mechanical resistance. COROZINC M can be painted over with any saponification-resistant 1K or 2K system (no alkyd resins). COROZINC M can also be used as a shop primer.

COROPUR 1K-FH intermediate micaceous iron coating is primarily used, in combination with moisture-curing systems, as an intermediate coating in corrosion protection systems from corrosivity category C3. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR Teer is a combination of a moisture-curing (FH) polyisocyanate and tar. COROPUR Teer is, comparable to the usual 2-component epoyy- or polyurethane tar coating materials, particularly suitable for the long-term corrosion protection of all steel surfaces. It is particularly characterized by high abrasion resistance, chemical resistance and low water and water vapour diffusion. Permanent temperature resistant: 60 °C up to a maximum of 80 °C

COROPUR is a moisture-curing, light, weather and chemical resistant top coat based on polyurethane resin. COROPUR can be applied at low temperatures and high humidity without any problems. The rapid drying and hardening of the coating film allows the coated objects to be manipulated quickly, thus reducing downtimes.

Primer and paint coating in one. The moisture-curing PU coating contains active corrosion protection pigments and thus combines the high mechanical properties of polyurethane with the corrosion protection properties of comparable cross-linked systems. It is also characterized by very fast drying, which results in shorter service lives. The dry layer can be cleaned with solvent (grease, etc.) after assembly. Easy repair even under bad conditions.

COROPUR 1K-FH intermediate micaceous iron coating is primarily used, in combination with moisture-curing systems, as an intermediate coating in corrosion protection systems from corrosivity category C3. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR LS 1K-FH finishing micaceous iron coating serves primarily, in combination with moisture-curing systems, as a high-quality top coat. The special, lamellar structure of the iron mica pigmentation, in combination with the PU binder, results in coatings with excellent water and corrosion resistance. COROPUR LS can be applied by airless application to vertical surfaces with a dry film thickness of up to 150 µm.

COROPUR 89 is a moisture-curing, light, weather and chemical resistant top coat based on polyurethane resin. COROPUR 89 can be applied at low temperatures and high humidity without any problems. The rapid drying and hardening of the coating film allows the coated objects to be manipulated quickly, thus reducing downtimes. Corresponds to the specifications according to TL/TP-KOR – Steel structures; Annex E; Sheet 89.

COROPUR is a moisture-curing, light, weather and chemical resistant top coat based on polyurethane resin. COROPUR can be applied at low temperatures and high humidity without any problems. The rapid drying and hardening of the coating film allows the coated objects to be manipulated quickly, thus reducing downtimes.

AQUAPERL T® ist ein lösemittelfreies 2-Komponenten Epoxid/Amin-System, frei von CMR-Stoffen. Designed für den dauerhaften Innenschutz von Stahl- sowie Betonkonstruktionen bei Wasserkontakt entweder im Mehrschichtaufbau mit Glasmattenverstärkung um eine mögliche Rissbildung bei Betonkonstruktionen bis zu einem gewissen Grad zu verhindern, oder als Einschichtlackierung auf Beton und Stahluntergründen zur Gewährleistung der Trinkbarkeit von Wasser bei Speicherung oder Durchleitung.

ECLON EP 2K-micaceous iron is a high-quality scale armour coating with high mechanical and chemical resistance. Dry film thicknesses of up to 150 µm can be achieved in a single pass. The pigmentation with micaceous iron ore creates a rough surface in addition to the barrier effect desired in corrosion protection. The best prerequisite for a perfectly adhering PU-based top coat.

COROPUR NonAbrasive is a tough elastic, highly abrasion resistant coating material. Particularly suitable for internal coating and thus long-term corrosion protection of pressure pipes and other steel surfaces. COROPUR NonAbrasive is characterized by low water and water vapor diffusion. Allows thick layer application up to 400 µm even on vertical surfaces. Gloss and UV-resistant coatings are achieved with the correspondingly resistant variant COROPUR NonAbrasive 2K-FH finishing coating LS.

COROPUR Teer 21 is an extremely fast-drying, moisture-curing polyurethane in combination with coal tar and micaceous iron ore. Particularly suitable as a thick-layer top coat on primed substrates. As a single layer, i.e. without primer for medium-heavy corrosion protection such as for shipbuilding, industry in immersion or underwater applications (for a long functional life). pH range 5–10.

COROPUR NonAbrasive is a combination of moisture-curing (FH) polyisocyanates. COROPUR NonAbrasive is, comparable to the usual 2-component epoyy- or polyurethane tar coating materials, particularly suitable for the long-term corrosion protection of all steel surfaces. It is particularly characterized by high abrasion resistance, chemical resistance and low water and water vapour diffusion. The light and weather resistance is good even in high sunlight. This enables its use in industrial, marine and alpine climates.

COROPUR TF 21 is an extremely fast-drying, moisture-curing polyurethane in combination with micaceous iron ore. Particularly suitable as a thick-layer top coat on primed substrates. As a single layer, i.e. without primer for medium-heavy corrosion protection such as for shipbuilding, industry in immersion or underwater applications (for a long functional life). pH range 5–10.

AQUAPERL T® ist ein lösemittelfreies 2-Komponenten Epoxid/Amin-System, frei von CMR-Stoffen. Designed für den dauerhaften Innenschutz von Stahl- sowie Betonkonstruktionen bei Wasserkontakt entweder im Mehrschichtaufbau mit Glasmattenverstärkung um eine mögliche Rissbildung bei Betonkonstruktionen bis zu einem gewissen Grad zu verhindern, oder als Einschichtlackierung auf Beton und Stahluntergründen zur Gewährleistung der Trinkbarkeit von Wasser bei Speicherung oder Durchleitung.